Floor drain FURO 148

För industri m.m. Finns för flera belastningsklasser.

Valfri längd x bredd 150 mm.
Kvalitet rostfritt EN 1.4301 (SS 2333), alt. syrafast rostfritt kval. EN 1.4404 (SS 2348).
För ingjutning i betonggolv.
Rännöverdelar för klinkergolv, massagolv samt stålslipat betonggolv som är vridbara 360°, vinkelställbara och teleskopiska.
Golvrännan har urtagbart vattenlås med handtag.
EPDM-gummitätningar enligt EN 681-1 typ Wc.
Rostfritt rutgaller, utfört i delar med max vikt 8 kg per del.
Installationstillbehör som ingår: Levereras täckt för att hindra betong från att rinna ner i rännan under gjutning. Rejäla fästöron för förankring i bjälklaget. Dessa ger möjlighet till enkel höjdjustering ovanifrån. Vid massagolv ingår ursparingslister på vidhäftningsflänsar.

R50 For areas with medium weight traffic. Tested acc. to EN 1253-1 with 33 kN load.
M125 For areas with truck traffic. Tested acc. to EN 1253-1 with 85 kN load.

Variants

Variable length:

Length (min-max) 500–20000 mm, in 100 mm increments.
Fixed width: 150 mm.

Variable depth:

100 mm, a good choice for lengths up to 8000 mm.
150 mm, recommended for lengths 8000–20000 mm.

Outlet placement:
The standard is a centered outlet, but it is possible to choose a different placement.

Specify c/c from the left.

Clinker floor K3

Floor material: Clinker in adhesives

Water proofing: Floor without waterproofing

Water proofing drain flange: None

Resin flooring

Floor material: Resin flooring

Water proofing: Compound floor

Water proofing drain flange: Recess for resin floor

Concrete floor

Floor material: Concrete floor

Water proofing: Floor without waterproofing

Water proofing drain flange: None

Dimensions for FURO 148 floor channel.

Construction dimensions for FURO 148 floor channel:

S1: 425 mm
F1: 365 mm

Drains and channels always have a connection pipe and their water flow (V.g.) to consider. Water flow is always measured from the so-called bottom line of the pipe.

To facilitate product selection, we specify the total height (H) of our drains and channels. The total height is the distance from the finished floor surface to where the water exits the product. For bottom outlets, the measurement point is where the spigot begins.

The total height (H) is always made up of the top depth (D) plus the outlet section of the product. If the top depth is increased, the total height will also increase, affecting the product's water flow.

Dimensions for FURO 148:

The upper part depth (D) can vary between 100 and 150 mm. (100 mm is standard for lengths up to 9000 mm).
The total height (H) of FURO 148 thus ranges between 217 and 267 mm. (217 mm is standard for sizes up to 8000 mm).
If an extension or inlet part is selected, the total height (H) increases by 60 mm.

Slope toward the outlet:

The product’s slope toward the outlet varies depending on the length and chosen upper part depth. For the standard design with a centrally positioned outlet, the following applies:

For lengths up to 8000 mm and recommended depth of 100 mm, the slope toward the outlet is at least 1%.
For lengths between 8000 – 20 000 mm and recommended depth of 150 mm, the slope toward the outlet is at least 0.9%.

For requirements other than the above recommendations, the slope will be affected.