Floor drain FURO 153

Golvränna med upplyftbar sandfångslåda. För industri m.m. Finns för flera belastningsklasser.

Valfri längd x bredd 300 mm.
Kvalitet rostfritt EN 1.4301 (SS 2333) alt. syrafast rostfritt EN 1.4404 (SS 2348).
För ingjutning i betonggolv.
Rännöverdelar för klinkergolv, massagolv samt stålslipat betonggolv som är vridbara 360°, vinkelställbara och teleskopiska.
Gavelplacerad utloppsdel.
Golvrännan har urtagbart vattenlås med handtag.
EPDM-gummitätningar enligt EN 681-1 typ Wc.
Rostfritt rutgaller, utfört i delar med max vikt 8 kg per del.
Med upplyftbar sandfångslåda, volym 5 liter.
Sandfångsfunktionen bygger på sedimenteringsprincipen och fungerar bäst vid låga flöden. Vid höga flöden följer det lätta materialet med ut i avloppet.
Installationstillbehör som ingår: Levereras täckt för att hindra betong från att rinna ner i rännan under gjutning. Rejäla fästöron för förankring i bjälklaget. Dessa ger möjlighet till enkel höjdjustering ovanifrån. Vid massagolv ingår ursparingslister på vidhäftningsflänsar.

L15 For areas with light weight traffic. Tested acc. to EN 1253-1 with 10 kN load.
R50 For areas with medium weight traffic. Tested acc. to EN 1253-1 with 33 kN load.
M125 For areas with truck traffic. Tested acc. to EN 1253-1 with 85 kN load.

Variants

Variable length (mm):

Length (L) = 600–2000 (in increments of 100)
Fixed width = 300

Variable depth (mm):

Depth (D) = 192, a good choice for lengths up to 2000.
Depth (D) = 232, recommended for lengths between 2000–6000.
Depth (D) = 312, recommended for lengths over 6000.

The channel depth (Rd) thereby varies between 80, 120, and 200.

Outlet placement:

The standard is an outlet section positioned at the end, but it is possible to choose the placement.

Specify c/c from the left.

For more information, see the section: "Water flow, total height, upper part depth, and slope towards outlet".

Clinker floor K3

Floor material: Clinker in adhesives

Water proofing: Floor without waterproofing

Water proofing drain flange: None

Resin flooring

Floor material: Resin flooring

Water proofing: Compound floor

Water proofing drain flange: Recess for resin floor

Concrete floor

Floor material: Concrete floor

Water proofing: Floor without waterproofing

Water proofing drain flange: None

Dimensions for FURO 153 floor channel:

*The product has a slope towards the outlet.

For more information, see the section:
"Water flow, total height, upper part depth, and slope towards the outlet".

Construction dimensions for FURO 153 floor channel:

S_1: = 395 mm
_F1: = 345 mm

Drains and channels always have a connection pipe and their water flow (V.g.) to consider. Water flow is always measured from the so-called bottom line of the pipe.

To facilitate product selection, we specify the total height (H) of our drains and channels. The total height is the distance from the finished floor surface to where the water exits the product. For bottom outlets, the measurement point is where the spigot begins.

The total height (H) is always made up of the top depth (D) plus the outlet section of the product. If the top depth is increased, the total height will also increase, affecting the product's water flow.

Dimensions for FURO 153:

Upper part depth (D) can be switched between 192, 232, and 312 mm (232 mm is a good choice for lengths between 2000–6000 mm). The channel depth (RD) then changes between 80, 120, and 200 mm.
Total height (H) for FURO 153 thus varies between 309, 349, and 429 mm (349 mm is a good choice for lengths between 2000–6000 mm).
If an extension part or inlet part is selected, the total height (H) increases by 60 mm.

Slope towards the outlet:
The product's slope towards the outlet varies depending on length and chosen upper part depth. With the standard configuration and end-positioned outlet, the following applies:

For lengths up to 2000 mm and recommended depth of 192 mm, the slope towards the outlet is at least 1 %.
For lengths between 2000–6000 mm and recommended depth of 232 mm, the slope towards the outlet is at least 1 %.
For lengths between 6000–20000 mm and recommended depth of 312 mm, the slope towards the outlet is at least 0.7 %.

For needs other than the above recommendations, the slope is affected.