Floor drain FURO 149

Floor drain FURO 149

Golvränna med upplyftbar sandfångslåda. För industri m.m. Finns för flera belastningsklasser.
  • Valfri längd x bredd 150 mm.
  • Kvalitet rostfritt EN 1.4301 (SS 2333) alt. syrafast rostfritt EN 1.4404 (SS 2348).
  • För ingjutning i betonggolv.
  • Rännöverdelar för klinkergolv, massagolv samt stålslipat betong golv som är vridbara 360°, vinkelställbara och teleskopiska.
  • Gavelplacerad utloppsdel.
  • Golvrännan har urtagbart vattenlås med handtag.
  • EPDM-gummitätningar enligt EN 681-1 typ Wc.
  • Rostfritt rutgaller, utfört i delar med max vikt 8 kg per del.
  • Med en upplyftbar sandfångslåda, volym 2,0 liter. Sandfångsfunktionen bygger på sedimenteringsprincipen och fungerar bäst vid låga flöden. Vid höga flöden följer det lätta materialet med ut.
  • Installationstillbehör som ingår: Levereras täckt för att hindra betong från att rinna ner i rännan under gjutning. Rejäla fästöron för förankring i bjälklaget. Dessa ger möjlighet till enkel höjdjustering ovanifrån. Vid massagolv ingår ursparingslister på vidhäftningsflänsar.

Variants

FURO115_VA_1.jpg
FURO149_VA_2.jpg
FURO149_BMATT_1.png

Dimensions for FURO 149 floor channel:

  • Depth: For a length of 2000 mm, the channel's depth increases.
Byggmått_ränna_SM_1.jpg

Construction dimensions for FURO 149 sand trap channel:

S1: 425 mm

F1: 365 mm

Drains and channels always have a connection pipe and their water flow (V.g.) to consider. Water flow is always measured from the so-called bottom line of the pipe.

To facilitate product selection, we specify the total height (H) of our drains and channels. The total height is the distance from the finished floor surface to where the water exits the product. For bottom outlets, the measurement point is where the spigot begins.

The total height (H) is always made up of the top depth (D) plus the outlet section of the product. If the top depth is increased, the total height will also increase, affecting the product's water flow.

Dimensions for FURO 149:

  • Upper part depth (D) can be switched between 192, 232, and 312 mm (232 mm is a good choice for lengths between 2000–6000 mm). The channel depth (RD) then changes between 80, 120, and 200 mm.
  • Total height (H) for FURO 149 thus varies between 309, 349, and 429 mm (349 mm is a good choice for lengths between 2000–6000 mm).
  • If an extension part or inlet part is selected, the total height (H) increases by 60 mm.
     

Slope towards the outlet:
The product's slope towards the outlet varies depending on length and chosen upper part depth. With the standard configuration and end-positioned outlet, the following applies:

• For lengths up to 2000 mm and recommended depth of 192 mm, the slope towards the outlet is at least 1 %.
• For lengths between 2000–6000 mm and recommended depth of 232 mm, the slope towards the outlet is at least 1 %.
• For lengths between 6000–20000 mm and recommended depth of 312 mm, the slope towards the outlet is at least 0.7 %.

For needs other than the above recommendations, the slope is affected.

126S75_utlopp.png
S 75

Side outlet Ø75 mm

Capacity 2,2 l/s

126B75_utlopp.png
B 75

Bottom outlet Ø75 mm

Capacity 2,7 l/s

126B110_utlopp.png
B 110

Bottom outlet Ø110 mm

Capacity 2,2 l/s
 

Trap

Trap

Trap included as standard.
Can be retrofitted.

Part no. 126VH2

Closable trap

Closable trap

A trap that can be shut off with a key. When choosing accessories, an extension part is required.

Part no. 126VA2

Trap with odor seal

Trap with odor seal

Trap with mechanical odor seal.

Part no. 126VL12

Lifting tool

Lifting tool

Lifting tool for grating and perforated plates.

Part no. 1LK1

Strainer basket, 2,6 liters

Strainer basket, 2,6 liters

Large strainer basket in stainless steel designed to effectively capture larger particles and debris that may flow with the water in the drainage system.

  • Volume: 2.6 liters

Part no. 126SK31

Sand trap, 2,0 liters

Sand trap, 2,0 liters

Sand trap included as standard.

  • Volume: 2.0 liters.

Part no. 126SF31

Sand trap, 2,0 liters

Sand trap, 2,0 liters

Large sand trap included as standard,

  • Volume: 2.0 liters.

Part no. 126SF31-200

Key for water trap

Key for water trap

Key for locking Vater trap 126VA2.

Part no. 1NV2

Grounding braid

Grounding braid

Grounding braid for equipotential bonding.

Part no. 1VJF

Screwed-down grate

Screwed-down grate

Grating fastened with screws.

Part no. 1VFG

Inlet

Inlet

Inlet with 50 mm smooth socket for easy connection.

Part no. 1VIN50

Without trap

Without trap

Floor drain without a trap. The trap can be retrofitted.

  • Capacity: 4 liters/second.

Part no. 1VSU126

Sealant Aqua Tät

Sealant Aqua Tät

Sealant Aqua Tät for plastic flooring. Used under the flooring when installing the clamping frame.

Part no. 1AQUAT40

Mounting, threaded rod

Mounting, threaded rod

Easy adjustment from above.

  • Height 300 mm.
  • Foot diameter = 100 mm.

Part no. 1SB30

Bits for plastic mounting rod

Bits for plastic mounting rod

For easy height adjustment of plastic mounting rod.

Part no. 1BITS16

Plastic mounting rod

Plastic mounting rod

Mounting rod that allows for easy adjustment from above.

  • Height: 300 mm
  • Foot diameter: 100 mm.

Use together with Installation accessories "Bits for plastic mounting rod".

Part no. 1SB40

Documents

Technical overview
SH.png BVB.svg

Do you have any questions?

Do you have questions and concerns about production or do you need help with planning?

Common questions Contact us

BIM

Do you need BIM or CAD files for your project? Download the files you need by clicking the buttons below.

Magicad Cloud MagiCAD Selection tool